Lobangs for watch winders

[Alexdeasa]

congrats... But as the brothers here mentioned, be sure to look out for the motor, winding just 1 watch may damage it over time... Oso be sure tat if u put two watches on the holder, ensure they require the same winding specs.

O that a bit bad!
Now I only have two watch, one wearing, one at home in the winder.
That mean I need to buy one more watch but my CO will kill me .
Maybe can take one of battery watch to put together with the auto watch to wind together

[jazz_samz]

congrats... But as the brothers here mentioned, be sure to look out for the motor, winding just 1 watch may damage it over time... Oso be sure tat if u put two watches on the holder, ensure they require the same winding specs.

Thz for all the info. But I got one at eBay at a super cheap price. Is a 4watch two motor one. Got it at only US$106 include shipping

[Alexdeasa]

Thz for all the info. But I got one at eBay at a super cheap price. Is a 4watch two motor one. Got it at only US$106 include shipping

[sys12345]

So whats happening here? It looks like only a 1 or 2 fellows interested in Luxupak, how to MO? If no one else is interested, then i guess u guys had better order on your own instead of waiting.

[triton]

Triton, actually, that watch winder I refer to is found in Hobbylink website.. :P

ok. personally i still prefer to get winders locally for safety. no doubt there are technicians here who can service the winders. also, if after adding the tax and freight cost, it does not cost much difference, then i think local is the way to go.

[triton]

bro, think u got yr eilux 1-2 yrs ago? prices have gone up...my single winder cost only $150+ then...now it's $230+ i think...

ok. was quoted about 800 before discount. even if i put 100 more, the cost per motor is still cheaper.

[jazz_samz]

Triton, actually, that watch winder I refer to is found in Hobbylink website.. :P

[wolfeyes1974]

jazz_samz: the one you mentioned, if im not mistaken should be running on 2 separate motors. this means that if you put 2 watches on 1 holder, both watches need to be wound in the same direction. this would mean the left holder is independent of the right holder. i could be wrong, best is email and clarify.

wolfeyes1974: based on a 1.4 exchange rate, it would cost about 630 which would put each motor for 315. i got an eilux triple winder for about 700 which allows me to have 3 separate motors, aka about 233 per motor.

abit hard to compare here because one is apple and the other is orange. however, if u already got 2 pairs of watches which requires smiliar TPD and winding direction, then this model might be suitable.

bro, think u got yr eilux 1-2 yrs ago? prices have gone up...my single winder cost only $150+ then...now it's $230+ i think...

[triton]

hey bros... Ask u all ah... Is it reasonable for a 4 pc watch winder that winds 2watches on a left holder and 2 watches on right holder, made of solid oak, runs on AC/DC and priced at S$450 ???

if it's running using 2 motors and allow you to have directional options and TPDs programming...$450 is consider reasonable....

jazz_samz: the one you mentioned, if im not mistaken should be running on 2 separate motors. this means that if you put 2 watches on 1 holder, both watches need to be wound in the same direction. this would mean the left holder is independent of the right holder. i could be wrong, best is email and clarify.

wolfeyes1974: based on a 1.4 exchange rate, it would cost about 630 which would put each motor for 315. i got an eilux triple winder for about 700 which allows me to have 3 separate motors, aka about 233 per motor.

abit hard to compare here because one is apple and the other is orange. however, if u already got 2 pairs of watches which requires smiliar TPD and winding direction, then this model might be suitable.

[seiko.citizen]

Interested but how is this MO going to work? The following needs to be agreed upon:

1) Make
2) Model
3) Price

So unless everyone is prepared to go for exactly the same winder, else how are u able to secure a better deal?

usually when i organise MOs i insist that everyone agree to the same make. in my opinion model not so much an issue, but of course it is better if all is the same model.

finally price will naturally fall into place after considering the above criterias.

volume orders is more important as such, from my view point, not everyone need to agree on same model.

If u guys are interested in Luxupak, i may be able to assist since i've been in touch with them. I'm considering getting the 3 watch winder from Luxupak. Good thing is that they now have 220V AC/DC adapter. Its a thing to take note as some other US based winders only comes with a 110V AC/DC adapter.

you would be in a very good position. since you are repeat customer

[marineguy8888]

Considering the 1pcs ww3618 and 2 pcs WW01911 Leather Single Watch Winder .

[sys12345]

If u guys are interested in Luxupak, i may be able to assist since i've been in touch with them. I'm considering getting the 3 watch winder from Luxupak. Good thing is that they now have 220V AC/DC adapter. Its a thing to take note as some other US based winders only comes with a 110V AC/DC adapter.

yeah. agreed. think marineguy888 and me likely to go for Luxupak

[triton]

Interested parties:

1) pet

2) marineguy8888

3) triton

4) Nakedtoes ( double or triple winder)

I am ok with any brand but must be reliable one.. best is we can stick to one brand and then decide how many winder we need..

yeah. agreed. think marineguy888 and me likely to go for Luxupak

[nakedtoes]

Interested parties:

1) pet

2) marineguy8888

3) triton

4) Nakedtoes ( double or triple winder)

I am ok with any brand but must be reliable one.. best is we can stick to one brand and then decide how many winder we need..

[sys12345]

Interested but how is this MO going to work? The following needs to be agreed upon:

1) Make
2) Model
3) Price

So unless everyone is prepared to go for exactly the same winder, else how are u able to secure a better deal?

need to agree on a single manufacturer too then we can start talking with them once we have a rough estimate on quantity required.

i think better to PM so i can get the ball rolling once we have numbers